Saniline washdown ball bearing units
are designed for
the ultimate in
FOOD SAFETY.
Food-Grade Sanitary design for
HACCP/HARPC compliance
IP69K certified
COC 100% stainless steel washdown ball bearing units have achieved IP69K certification and feature our relubrication-free design. Our new concentric OCCLOC™, 8 slot locking system doesn’t damage shafting and is easy to mount and dismount. It has great holding power even with the undersized commercial shafting.
IP69K TEST
The water intrusion tests themselves are done by placing the product on a turntable with a rotational speed of 5 ±1 revolutions per minute. The product is then sprayed at close range at a rate of approximately 4 gallons/16 liters per minute with water pressure of between 1160-1450 psi, at a temperature of 176°F/80°C. The nozzle from which the water is sprayed is held between 4 and 6 inches from the product, at a variety of angles.
The IP69K rating provides protection against ingress of dust and high temperature, high pressure water – making products with this certification ideal for use in conditions where equipment must be carefully sanitized. The IP69K rating is the highest protection available.
Lubricated for life
COC’s sealing system with stainless steel flinger is designed to withstand frequent high pressure washdowns. The IP69K rating is for high pressure and high temperature washdown applications. Lubricated for life with NSF approved H1 food grade grease, this maintenance free solution allows better cleaning of machinery and increased uptime.
Clean-in-Place
Minimizing the contact area with the machine helps eliminate bacteria harborage and our stand-off housings allow for clean-in-place (CIP) operation. They have mostly 1/2″ stand-off clearance to meet HACCP/HARPC compliance.
CLEAN SHAFT with OCCLOC™
8 SLOTS CONCENTRIC LOCKING SYSTEM
Provides clamping force around the entire shaft.
COC’s original OCCLOC™ uses two setscrews located 120° apart in the locking collar over the 8-slot inner ring. As the setscrews are tightened, they push on the inner ring while simultaneously drawing the locking collar upward, clamping the inner ring securely from both sides.
Locking collar is drawn upward
Inner ring clamped from both sides
The same clamping action at both setscrews.
OCCLOC™ leaves no marks on the shaft. OCCLOC™ clamps securely onto undersized commercial shafting and provides reliable holding power on hardened shafts where stainless steel setscrews may slip. OCCLOC™ saves you money by allowing the use of less expensive commercial shafting.
- Easiest to install as easy as a setscrew lock
- Can use Commercial Shafts (h9 fit)
- No damage to the shafting
- Reliable on hardened shafts where stainless setscrews may slip.
Set screw UC-Style Locking Options
- Greater compatibility with existing equipment
- More cost-effective replacement options
- Flexible locking options without compromising performance
Stainless steel safety cover
Our patented stainless steel safety cover installs without any additional machining of the housing. Although our IP69K-certified units do not require safety covers for additional protection, they are available as an option.
Our stainless steel safety covers are easy to install, remove, and clean. Two small tabs engage the bearing slots on the front of the housing. Simply twist the cover until it clicks into place. The cover does not require sealing and features two drain holes to reduce heat and moisture buildup.
Since this is a relubrication-free design, no grease purging occurs after the initial run-in period. An open, ventilated design helps prevent moisture from being trapped inside the cover.
100% stainless steel units including safety covers are recyclable and we don’t use any plastic materials. The plastic and nickel-plated housings are good cost savings for some applications but when they get scratched, they can become entrapment points for bacteria and rust from damaged nickel-plated steel. We believe stainless steel units are safer and our relubrication-free design reduces grease consumption, water usage for cleaning, and maintenace costs. The longer you use our bearings, the better it is for the planet.
Scan on-site
Our unique octagonal stainless steel housing is smooth and easy to clean. The flat surface is designed to accommodate a laser-marked QR code. The QR code provides instant access to installation instructions, product information, and a unique serial number for full traceability.
